Chinese translation for "hinge support"
|
- 高强螺栓连接钢结构
铰轴支座
Related Translations:
- Example Sentences:
| 1. | Research and application of hinged support technology in tunnel with soft rock and complex roof
软岩复合顶板煤巷耦合支护技术的研究与应用 | | 2. | Optimal design of the stability of compression bar under the constraint of elastically hinged support at both ends
两端弹性铰支约束下压杆稳定的优化设计 | | 3. | Hinge support sleeve reduces friction and minimizes water hammer through independent plate suspension ( on larger sizes )
铰链支撑套管减小摩擦，并将通过独立阀瓣中止时的水锤现象降到最小程度(更大的通径) 。 | | 4. | Whether the axle pin can be smoothly bolted into the hinge support is crucial for the whole project . to achieve this goal , a prefabricated taper pin was used to induce the axle pin
铰支座穿轴销顺利与否是施工的关键，采用提前做一锥销来引导轴销的方法来实现。 | | 5. | As we know , support at the both straight edge of acmr is a elastic support between the hinged support and fixed support , and its stiffness is variational . so the relation between support stiffness and load - carrying capability of acmr is worth to be studied
众所周知，实际工程中波纹拱两端的直边支座处于铰支和固支之间，属一弹性支座，其弹性刚度是变化的，支座刚度与波纹拱结构受力性能及稳定承载力之间的关系是一个非常值得研究的课题。 | | 6. | After an introduction to the research on the software for the design of the variant steel arched girder construction , the creation of the structural model , the structure of the supporting seat , the design of the variant arched girder , and the measures taken to ensure the stability of the plane surface of the arched girder , the thesis goes to study the methods for the hoisting and the angle setting of the long - span arched girders , as well as the bolting of the axle pin in the hinge support
论文首先对变异钢拱架结构设计可采用的软件、结构模型的建立、支座构造形式、变异拱梁的设计，以及保证拱梁平面外稳定所采取的措施等进行了研究，然后研究了大跨度变异钢拱架弧形梁吊装、角度的调整、铰支座穿轴销等的施工方法，最后对施工完成后的位移进行了实际量测。 | | 7. | In this study , sts - - the steel construction design module of pkpm , a software program of china " s institute of the construction science - - is employed to create the construction model in order to study the construction of the supporting seat . a mechanical analysis of the variant arched girders was implemented , with the result that consturction documents meeting mechanical requirements were designed for the hinge support , the roller support and the steel girders
本文采用中国建筑科学研究院pkpm软件的钢结构设计模块sts ，从结构建模入手，根据规范要求研究了支座的构造形式，通过对变异拱梁的力学分析，设计出符合力学模型的铰支座、滑移支座和变异拱处钢梁的施工图。 |
- Similar Words：
- "hinge slot" Chinese translation, "hinge socket" Chinese translation, "hinge spine" Chinese translation, "hinge stop" Chinese translation, "hinge straps" Chinese translation, "hinge tooth" Chinese translation, "hinge tooth; tooth" Chinese translation, "hinge torque" Chinese translation, "hinge trough" Chinese translation, "hinge type" Chinese translation
|
|
|
